# How to Prime a Well Pump: Jet Pump Steps and When Not To

> How to prime a well pump: breaker off, fill the priming port, seal the plug, restart. Expect water in 1–2 minutes. Jet pump steps; submersibles differ.

URL: https://waterwelldrillingweatherford.com/news/how-to-prime-a-well-pump/

How-To

Only above-ground jet pumps are primed by hand, and a manufacturer manual expects water within 1–2 minutes of restart. Most Parker County wells are too deep for that kind of pump, so check which one you have first.

How to prime a well pump: turn off the breaker, open a faucet to release pressure, remove the priming plug, fill the pump housing with water, reseal the plug with PTFE tape and restart. Flotec's manual expects water within **1–2 minutes**. Submersible pumps sit in the water and are not primed by hand.

Key takeaways

- Only above-ground **jet pumps** are primed by hand. Submersible pumps sit underwater and do not lose prime, unless the well level falls below the pump ( [InspectApedia](https://inspectapedia.com/water/Prime_The_Well_Pump.php)).
- Flotec's owner's manual says to start the motor only after the pump is filled, and that water should arrive in **1–2 minutes**; if not, repeat the fill ( [Flotec FP2521 manual](https://www.pentair.com/content/dam/extranet/web/nam/flotec/manuals/fp1033-fp2521-shallow-well-jet-tank-iom.pdf)).
- Never run a jet pump dry: the manual warns it can overheat and damage the seal, and that the motor needs **20 minutes** to cool before you handle it ( [Flotec FP2521 manual](https://www.pentair.com/content/dam/extranet/web/nam/flotec/manuals/fp1033-fp2521-shallow-well-jet-tank-iom.pdf)).
- A shallow-well jet is built for pumping depths of **25 ft or less** with a maximum lift of **20 ft** at sea level, roughly 19 ft at Weatherford's 1,053 ft elevation (Flotec manual; [Wikipedia](https://en.wikipedia.org/wiki/Weatherford,_Texas); our arithmetic).
- New wells near Weatherford finish with water about **110 ft** down, far beyond that lift ( [TWDB driller reports, per our low-pressure guide](https://waterwelldrillingweatherford.com/learn/low-water-pressure-on-a-well/)).
- A pump that keeps losing prime usually has a leaking foot valve, check valve or suction pipe, so re-priming only buys time ( [InspectApedia](https://inspectapedia.com/water/Well_Pipe_Foot_Valve.php)).

[Water Well Drilling Weatherford](https://waterwelldrillingweatherford.com/) hears this one when the taps sputter and the pump hums with no water: how to prime a well pump. The answer depends on the pump you own. Above-ground jet pumps are primed by hand; submersibles are not. Below are the jet pump steps, the limits that matter in Parker County, and the point where a [well pump repair](https://waterwelldrillingweatherford.com/services/well-pump-repair/) call beats another bucket of water.

## What does it mean to prime a well pump?

Priming means filling the pump housing and suction line with water so the pump can create suction instead of spinning in air. A jet pump pulls water up by vacuum, and air in the line breaks that vacuum. Fill the pump, and it can draw water again.

Flotec’s owner’s manual explains the mechanism: the impeller’s rotation creates a vacuum that pulls in more water, and in a shallow well that vacuum is enough to pull water to the pump ([Flotec FP2521 manual](https://www.pentair.com/content/dam/extranet/web/nam/flotec/manuals/fp1033-fp2521-shallow-well-jet-tank-iom.pdf)). The same manual says a pump that has a working foot valve, check valve and tight suction pipe should not need repriming in normal service. A pump that needs it again and again is telling you something else is wrong.

## Does your well pump need priming at all?

Only above-ground jet pumps do. A submersible hangs in the water down the well and pushes water up, so it has nothing to lose prime from. InspectApedia says submersible pumps do not lose prime because the pump is under water, with one exception: the well level dropping below the pump.

| Pump type | Hand priming? | Where it sits | Typical limit |
| --- | --- | --- | --- |
| Shallow-well jet | Yes | Above ground, at the tank or well house | Pumping depth of 25 ft or less (Flotec) |
| Deep-well jet | Yes, and harder | Above ground, with a jet down the well | Depends on the model’s lift rating |
| Submersible | No | In the water, at the bottom of the well | Set below the water level in the well |

This matters in Parker County. A shallow-well jet has a maximum lift of 20 ft at sea level, and the manual says lift drops about 1 ft for every 1,000 ft of elevation. At Weatherford’s 1,053 ft elevation ([Wikipedia](https://en.wikipedia.org/wiki/Weatherford,_Texas)) that works out to roughly 19 ft, our arithmetic from the manual’s rule. New wells near Weatherford finish with water about 110 ft down, and around Aledo about 176 ft ([TWDB driller reports, per our low-pressure guide](https://waterwelldrillingweatherford.com/learn/low-water-pressure-on-a-well/)). A hand-primed jet pump will not lift water that far, so a house well at those depths needs a submersible or a deep-well design, not a hand-primed shallow jet. Our [submersible vs jet pump](https://waterwelldrillingweatherford.com/news/submersible-vs-jet-pump/) comparison covers the choice, and the [depth guide](https://waterwelldrillingweatherford.com/learn/how-deep-are-water-wells-parker-county/) shows how deep local wells run.

If you cannot tell which you have, look at the well. A jet pump is a motor-and-housing unit you can see above ground, with a priming plug on top. A submersible shows only a pipe and cable going into the well cap.

## What do you need before you prime a well pump?

You need clean water, a funnel, a wrench for the priming plug, PTFE thread sealant tape and a way to confirm the power is off. Gather them first, so the pump is open for the shortest possible time.

- **A clean water source.** A garden hose or buckets. [InspectApedia](https://inspectapedia.com/water/Prime_The_Well_Pump.php) suggests using leftover system pressure or draining water from the pressure tank or water heater drain valve.
- **A priming port you can reach.** Flotec’s manual says a pipe tee in the discharge piping, with a plug, is needed to prime the pump properly. If your pump has no port, stop and call a licensed installer.
- **A look at the pump first.** Mad River Well Services advises inspecting the pump, hoses and valves for cracks and leaks before priming, and to fix any fault before priming ( [Mad River Well Services](https://www.madriverwell.co/7-steps-to-prime-a-well-pump)).

## How do you prime a well pump, step by step?

To prime a well pump, kill the power, release the pressure, fill the pump through the priming port, seal the plug and restart. Flotec’s instructions say not to start the motor until the pump has been filled with water.

The five steps in order. Illustration, not a photo of a real job.

1. **Turn off the pump breaker.** Flotec’s manual says to disconnect power before working on the pump, motor, pressure switch or wiring. InspectApedia also advises closing the main water valve between the pump and the house.
2. **Open a faucet to release pressure.** InspectApedia warns that if you open the port before releasing air and water pressure, “you’ll get soaked.”
3. **Fill the pump through the priming port.** Take out the plug, which [InspectApedia](https://inspectapedia.com/water/Prime_The_Well_Pump.php) places on top of the pump body, not the motor, and pour in water slowly until the housing is full. Watch the level and top it up if it drops.
4. **Seal the plug with PTFE tape.** Flotec’s manual says to use PTFE tape or a PTFE-based joint compound on the plug threads, then tighten. A loose plug lets air in.
5. **Restore power and watch.** Flotec says water should be pumped in 1 to 2 minutes. Then open the faucet farthest from the tank and let it run until the stream is steady, because the manual says air must be flushed out of the system after repriming.

On shallow lifts of 10 ft or less, Flotec says the pump will probably prime the first time. From 10 to 20 ft you may have to switch off and repeat the fill several times.

Key numbers from the sources cited in this article. Illustration, not a photo.

## How long can a jet pump run dry while you prime it?

Not long. Flotec’s manual says never to run the pump dry, because running without water may overheat the pump and damage the seal, and may cause burns to anyone handling it. Switch off if no water arrives.

The sources differ on the exact window. Flotec says water should be pumped within 1 to 2 minutes. InspectApedia says that if the pump keeps making a horrible noise for 45 seconds to a minute, turn it off and prime again, and warns that leaving it running for half an hour with no water is a different story. Take the shorter number. Flotec also says the motor runs hot normally and needs 20 minutes to cool before you handle it, and never to run the pump against a closed discharge, which can boil water inside the housing.

## Why does a well pump lose prime again?

A pump that loses prime repeatedly has an air leak or a failing valve, and priming only hides it. The usual suspects are a leaking foot valve at the bottom of the suction pipe, a bad check valve, a cracked or loose suction pipe, or an air leak at the well cap.

[InspectApedia](https://inspectapedia.com/water/Well_Pipe_Foot_Valve.php) describes the foot valve as a check valve with a strainer: it closes when the pump stops so the pipe stays full. When it leaks or jams, the pipe drains back into the well and fills with air. The same site notes that cloudy water full of tiny bubbles can point to an air leak in the suction line.

Two public cases show how stubborn the problem can be. On InspectApedia, a reader with a Goulds J5 jet pump on a deep well wrote on January 5, 2018 that the pump lost prime during power outages and cycled every 10 to 12 minutes with no water in use. The site’s answer was that losing prime in an outage usually means a leak in the well piping or a bad foot valve. The owner replaced a dripping air volume control, which cut the cycling but did not end it, and planned to pull the piping in spring. A January 2012 reader on the same site suspected a leaking foot valve on a roughly 20 ft well after pressurizing the system showed pressure and prime draining away. Neither thread reports a confirmed fix.

If the pump is running the whole time instead, see why a [well pump runs constantly](https://waterwelldrillingweatherford.com/news/well-pump-running-constantly/). If your pump has lost prime twice in a week, use our [no water from well guide](https://waterwelldrillingweatherford.com/learn/no-water-from-well/) to work through the other causes. A falling water level is one of them; see [is my well going dry](https://waterwelldrillingweatherford.com/learn/is-my-well-going-dry/).

## Author’s take: what would I do with a pump that won’t hold prime?

This section is the author’s analysis of the sources above, written by [Chris Fugate](https://waterwelldrillingweatherford.com/about/chris-fugate/), a water well driller with 24 years of experience. It draws conclusions from the cited evidence and does not describe any particular customer or job.

**Prime it once, and treat a second prime as a diagnosis, not a routine.** Every source here agrees on the mechanics. What a sealed pump and a good foot valve should do is hold water, so a pump that loses it is leaking somewhere you cannot see. The 2018 Goulds thread shows what happens when the leak is left until spring: months of short cycling on a pump that costs real money to burn out.

**Check the pump type before you reach for the hose.** In this county the water is often more than 100 ft down, far past what a hand-primed jet can lift. If the pump hums and gives no water, look for a tripped breaker, a failed pressure switch or a pump that needs pulling before you assume it lost prime.

## What does it cost when priming does not fix it?

Priming costs a few dollars of water and tape. When it does not fix the problem, the bill moves to the failed part. Submersible replacement at Parker County depths typically runs $1,800 to $4,500, per [our well pump replacement cost guide](https://waterwelldrillingweatherford.com/learn/well-pump-replacement-cost/), and our [repair or replace guide](https://waterwelldrillingweatherford.com/learn/repair-or-replace-well-pump/) explains how a technician decides.

Call a licensed pro if any of these apply:

- the pump runs without water after two or three careful primes;
- you see a tripped breaker, a burning smell or a hot motor;
- water or air keeps coming back after the foot valve or suction line is suspected;
- you cannot confirm the power is off or cannot reach a priming port.

Texas requires a license to install or repair a pump on a water well ([TDLR](https://www.tdlr.texas.gov/media/pdf/water-well-drillers-and-pump-installers-at-a-glance.pdf)). With no water at the house, see [emergency well pump repair](https://waterwelldrillingweatherford.com/emergency-well-pump-repair/). If the pump is old, [how long a well pump lasts](https://waterwelldrillingweatherford.com/news/how-long-does-a-well-pump-last/) helps you weigh repair against replacement, and if the pump runs but pressure is poor, [how to adjust a well pressure switch](https://waterwelldrillingweatherford.com/news/how-to-adjust-a-well-pressure-switch/) covers the controls.

## How was this guide researched?

This guide draws on one manufacturer owner’s manual (Flotec FP2521), InspectApedia reference pages, one well contractor’s guide, TDLR and TWDB records and two public reader cases. It contains no original measurements or field tests. The roughly 19 ft lift at Weatherford is arithmetic from the manual’s 1 ft per 1,000 ft rule and Wikipedia’s elevation figure. Reddit threads were blocked from our fetch tool and are not used. The steps follow one manufacturer’s manual; a different model’s manual wins if they differ, so read yours.

## Frequently asked questions

**How do you prime a well pump?**

Turn off the breaker, release pressure at a faucet, remove the priming plug, fill the pump housing with water, reseal the plug with PTFE tape and restart. Flotec's manual says water should be pumped in 1 to 2 minutes; if not, repeat the fill. Only above-ground jet pumps are primed this way.

**Do submersible well pumps need to be primed?**

No. InspectApedia says submersible well pumps do not lose prime because the pump is under water. If a submersible gives no water, the cause is usually the pump, the controls or the well itself, such as a water level that has dropped below the pump.

**How much water does it take to prime a well pump?**

Enough to fill the pump housing. The manuals we read give no single volume: Flotec says to fill the pump with water, and InspectApedia says to pour in slowly until the housing fills and to add more if the level drops. Keep adding until the level holds.

**How long can a jet pump run before it gets water?**

Flotec says water should be pumped in 1 to 2 minutes after restart. InspectApedia tells owners to switch off after 45 seconds to a minute of dry noise and prime again. Both agree you should not leave it running dry, which can damage the seal.

**Why does my well pump keep losing prime?**

A leaking foot valve, a leaking check valve, or an air leak in the suction pipe or at the well cap. InspectApedia says any leak that lets water drain out of the pump body and well piping can cause loss of prime. Re-priming is a temporary fix, not a repair.

**What happens if you don't prime a well pump?**

The pump cannot pull water and runs dry. Flotec's manual warns that running a pump without water may overheat it and damage the seal, and may burn people handling it. Switch it off and prime it first.

**Can I prime a deep well pump myself?**

A deep-well jet is primed much like a shallow one, but the work is harder and a leak may be far down the pipe. In Texas, installing or repairing a pump on a water well is licensed work under TDLR, so call a licensed pump installer for anything past a simple refill.

Sources

1. [Flotec (Pentair), Shallow Well Jet Pump/Tank System Owner's Manual, FP2521](https://www.pentair.com/content/dam/extranet/web/nam/flotec/manuals/fp1033-fp2521-shallow-well-jet-tank-iom.pdf)
2. [InspectApedia, How to prime the water pump](https://inspectapedia.com/water/Prime_The_Well_Pump.php)
3. [InspectApedia, Q&A on repeated loss of well pump prime (reader question Jan. 5, 2018)](https://inspectapedia.com/water/Repeated-Pump-Prime-Loss-FAQs.php)
4. [InspectApedia, Well foot valves and check valves on well piping](https://inspectapedia.com/water/Well_Pipe_Foot_Valve.php)
5. [Mad River Well Services, 7 Steps to Prime a Well Pump](https://www.madriverwell.co/7-steps-to-prime-a-well-pump)
6. [Wikipedia, Weatherford, Texas (elevation)](https://en.wikipedia.org/wiki/Weatherford,_Texas)
7. [Texas Department of Licensing and Regulation, Water Well Drillers and Pump Installers at a Glance](https://www.tdlr.texas.gov/media/pdf/water-well-drillers-and-pump-installers-at-a-glance.pdf)
8. [Texas Water Development Board, Submitted Drillers Reports](https://www.twdb.texas.gov/groundwater/data/drillersdb.asp)

## More from the news desk

- Explainer **[2 Wire vs 3 Wire Well Pump: Differences, Cost and Which to Choose](https://waterwelldrillingweatherford.com/news/2-wire-vs-3-wire-well-pump/).**
- Explainer **[Well Maintenance Cost: What a Year of Upkeep Runs in 2026](https://waterwelldrillingweatherford.com/news/well-maintenance-cost/).**
- Explainer **[Well Pump Short Cycling: Why It Happens and How to Stop It](https://waterwelldrillingweatherford.com/news/well-pump-short-cycling/).**

## Ask about your well

Faster by phone, any hour: [(817) 382-3840](tel:+18173823840)
