# Static Water Level in a Well: Parker County Data (2026)

> Static water level in a well, with Parker County data: a median 110 ft across 1,905 new wells, town-by-town levels, and how far below it pumps are set.

URL: https://waterwelldrillingweatherford.com/news/static-water-level-in-a-well/

Explainer

Guides explain how to measure a static water level. None says what it is near you, so we pulled the level from 1,905 recent Parker County driller reports and compared it with well depth and pump setting.

The static water level in a well is how far down the water stands, in feet below ground, once the pump has been off long enough for the well to rest. For new Parker County household wells it is a median of **110 ft**, and the middle half fall between **75 and 180 ft** (Texas Water Development Board driller reports, 2021–2026).

Key takeaways

- The median static water level in new Parker County household wells is **110 ft**, from **1,905** driller reports that include one ( [Texas Water Development Board](https://www.twdb.texas.gov/groundwater/data/drillersdb.asp), extract dated September 25, 2026).
- Only **40%** of the 4,746 new Parker County household well reports since January 2021 list a static level, so your own well report may not list it (our count of the same extract).
- Levels run from a median of **80 ft** at Poolville to **180 ft** at Aledo, and **21.8%** of wells report water 200 ft down or deeper (TWDB driller reports, 2021–2026).
- The median pump is set **100 ft** below the static level, and **5.1%** are set less than 50 ft below it (TWDB driller reports, 1,729 wells that report both).
- Oregon State University says to measure the static level after the well has rested several hours, and to take 4–6 readings a year for at least 5 years to see a trend ( [OSU Well Water Program](https://wellwater.oregonstate.edu/well-water/limited-water/measuring-well-water-level), 2026).

[Water Well Drilling Weatherford](https://waterwelldrillingweatherford.com/) gets asked what a normal static water level in a well is, and the honest answer is that most guides only explain how to measure it. This page uses the state’s own driller reports to show what the number actually looks like in Parker County, by town, by well depth and against pump setting. If your well is struggling, our guide on [whether your well is going dry](https://waterwelldrillingweatherford.com/learn/is-my-well-going-dry/) covers the symptoms.

Key numbers from the Texas Water Development Board driller reports, extract of September 25, 2026. Illustration, not a photo.

## What is the static water level in a well?

The static water level is the height of the water in the well, measured as feet down from the ground, when nothing is being pumped. Oregon State University defines it as “the water level in the aquifer from which you are pumping,” measured after the well has rested for several hours.

Resting matters because a running pump pulls the level down. Oregon State says to measure the static level, not the pumping or recovering level, when judging whether a well is going dry. The usual tool is an electric depth gauge, which the same page calls the easiest and most common method. The pumping level is the lower number a well settles at while water is being drawn, and the gap between the two is the drawdown.

4–6 readings a year How often Oregon State University suggests measuring a well's static level, for at least 5 years, to see a trend. Source: OSU Well Water Program, 2026

## What is the typical static water level in Parker County?

The typical static level in new Parker County household wells is 110 ft below ground. That median comes from the state’s driller reports for wells finished since January 2021, and the middle half of wells fall between 75 and 180 ft. The spread is wide, with one well in ten at 50 ft or shallower and one in ten at 250 ft or deeper.

| Metric | Value | Source |
| --- | --- | --- |
| New Parker County household wells, 2021–2026 | 4,746 | TWDB driller reports |
| Wells that report a static level | 1,905 (40%) | TWDB driller reports |
| Median static level | 110 ft | TWDB driller reports |
| Middle half (25th to 75th percentile) | 75–180 ft | TWDB driller reports |
| 10th and 90th percentile | 50 ft and 250 ft | TWDB driller reports |
| Mean static level | 133 ft | TWDB driller reports |
| Deepest reported | 530 ft | TWDB driller reports |

The mean sits above the median because a few wells report very deep water. Deeper levels are not rare, though. About 21.8% of wells report water 200 ft down or deeper, and 10.1% report 250 ft or deeper, while 41.6% report water above 100 ft.

Share of new Parker County wells by static water level

0–49 ft 8.8%

50–99 ft 32.8%

100–149 ft 23.1%

150–199 ft 13.5%

200–299 ft 18.2%

300 ft and deeper 3.6%

Scale: 0% to 40% of wells. Source: TWDB driller reports, 1,905 wells with a reported static level, 2021–2026.

Only about four in ten reports include the number at all, so treat it as a sample, not a census. Reporting also varies by area: 69% of Aledo reports list a static level, against 32% of Poolville reports (our count of the same extract).

## How does the static water level change from town to town?

It changes a lot. Counting wells by the mailing city on the report, the median static level is 80 ft at Poolville and 180 ft at Aledo, a gap of 100 ft inside one county. Weatherford sits in the middle at 110 ft, which is also the county median, and Azle and Springtown are shallower.

| Mailing city on report | Wells with a static level | Median static level | Middle half | Source |
| --- | --- | --- | --- | --- |
| Poolville | 207 | 80 ft | 60–100 ft | TWDB driller reports |
| Azle | 120 | 75 ft | 54–150 ft | TWDB driller reports |
| Springtown | 100 | 88 ft | 67–130 ft | TWDB driller reports |
| Weatherford | 1,026 | 110 ft | 80–170 ft | TWDB driller reports |
| Aledo | 297 | 180 ft | 140–220 ft | TWDB driller reports |

Medians and middle halves from TWDB driller reports, 2021–2026. Chart drawn by us from our counts.

Our [depth guide](https://waterwelldrillingweatherford.com/learn/how-deep-are-water-wells-parker-county/) groups wells by distance from each town rather than by mailing city, so its figures differ by a few feet, for example about 176 ft for Aledo against 180 ft here. Both agree on the pattern. Wells near [Aledo](https://waterwelldrillingweatherford.com/areas/aledo/) in the southeast of the county meet water far deeper than wells near [Poolville](https://waterwelldrillingweatherford.com/areas/poolville/) in the northwest. Towns with fewer than 30 readings under this mailing-city grouping are left out.

100 ft The gap between the median static level at Aledo (180 ft) and at Poolville (80 ft). Source: TWDB driller reports, 2021–2026

## How does static water level relate to well depth?

Deeper wells meet deeper water. Among Parker County wells that report a static level, those under 200 ft deep have a median of 65 ft, while wells of 400 ft and deeper have a median of 280 ft. Across all wells, the static level sits at a median of 45% of the total depth.

| Total well depth | Wells | Median static level | Source |
| --- | --- | --- | --- |
| Under 200 ft | 222 | 65 ft | TWDB driller reports |
| 200–249 ft | 751 | 80 ft | TWDB driller reports |
| 250–299 ft | 291 | 125 ft | TWDB driller reports |
| 300–399 ft | 488 | 200 ft | TWDB driller reports |
| 400 ft and deeper | 153 | 280 ft | TWDB driller reports |

The median well reaches 140 ft below its static level, and the middle half run 115–160 ft. A likely reason, in our reading and not a sourced finding, is that a driller stops once enough water-bearing rock lies under the static level to supply the house. That is why the [cost per foot of drilling](https://waterwelldrillingweatherford.com/news/water-well-drilling-cost-per-foot/) matters more at Aledo than at Poolville: the same yield costs more footage.

## How far below the static level is the pump set?

The median submersible pump is set 100 ft below the static level, and the middle half are set 80–130 ft below it. We could compare both numbers in 1,729 reports. Nearly six in ten pumps (58.2%) sit 100 ft or more below static, and 5.1% sit less than 50 ft below it.

| Pump setting below static level | Wells | Share | Source |
| --- | --- | --- | --- |
| At or above static level | 11 | 0.6% | TWDB driller reports |
| 1–49 ft below | 89 | 5.1% | TWDB driller reports |
| 50–99 ft below | 622 | 36.0% | TWDB driller reports |
| 100 ft or more below | 1,007 | 58.2% | TWDB driller reports |

The 11 pumps at or above the static level are probably entry errors or odd cases, and we do not read anything into them. The distance matters because the level falls while the pump runs (the flow a well can sustain is its yield, which we cover in [what is a good gpm for a well](https://waterwelldrillingweatherford.com/news/what-is-a-good-gpm-for-a-well/)), and a pump that sits just under the static level can run out of water at the start of a long draw. Our [submersible vs jet pump guide](https://waterwelldrillingweatherford.com/news/submersible-vs-jet-pump/) shows why almost every Parker County well is too deep for a jet.

Pump makers set limits in both directions. In a thread on Solar-Electric.com, a poster with a 300-ft well and an 85-ft static level asked where to set the pump. His driller said 20 ft off the bottom, while the pump maker said it should not go more than 40–50 ft below static. The page itself returned an access error to us, so we are relying on a search excerpt for those details and cannot say when the thread was written. It still shows why a setting depth is a decision, not a default.

## Is the static water level falling in Parker County?

The driller reports do not show a countywide decline, but they cannot prove there is none. The median static level for wells finished in each year was 110 ft in 2021, 100 in 2022, 120 in 2023, 110 in 2024, 115 in 2025 and 90 ft in 2026 so far. These are different wells each year, not repeat readings of one well.

The Upper Trinity Groundwater Conservation District plans for the aquifers to drop over time. Its 2023 management plan sets desired future conditions, which are average drawdowns from 2010 to 2080, for Parker County: 42 ft for the Antlers, 20 ft (outcrop) and 50 ft (downdip) for the Glen Rose, and 7 ft and 68 ft for the Twin Mountains. The district also says it will measure water levels at least annually. Our [explainer on the 2026 rule changes](https://waterwelldrillingweatherford.com/news/upper-trinity-groundwater-rules-2026/) covers what that means for new wells.

7 ft and 68 ft Planned average drawdown in the Twin Mountains aquifer by 2080 for Parker County, outcrop and downdip. Source: Upper Trinity GCD Groundwater Management Plan, 2023 (desired future conditions, from 2010 levels)

The same plan notes, from a 2009 TWDB count, that 5.4% of Parker County wells are completed in the Cross Timbers (Paleozoic) aquifers and 3.0% in alluvium. Those wells sit in different rock from the Trinity wells that dominate the table above, so their levels can differ.

### Try your own numbers

Enter your static level, pump setting depth and total depth from your well report. The result compares them with the Parker County medians above.

This only compares your numbers with state averages. It cannot tell you whether the pump has enough water while running. For that, see our [well problem checker](https://waterwelldrillingweatherford.com/well-problem-checker/).

## Author’s take: how I’d use a static water level

This section is the author’s analysis of the sources above, written by [Chris Fugate](https://waterwelldrillingweatherford.com/about/chris-fugate/), a water well driller with 24 years of experience. It draws conclusions from the cited evidence and does not describe any particular customer or job.

**Know the number before you need it.** Only 40% of recent reports list a static level, and a report you cannot find is a measurement you do not have. Measure it once, with the well rested, and write it down with the date. Oregon State’s advice of 4–6 readings a year is the right habit if you have a well that has ever sputtered.

**Judge the pump by the water above it, not by the static level alone.** A pump 100 ft under the static level has a cushion, and one 30 ft under it may not. If a well starts to sputter in late summer, the first question is how far the level drops while the pump runs, and our [low water pressure guide](https://waterwelldrillingweatherford.com/learn/low-water-pressure-on-a-well/) walks through the other causes first. Lowering a pump is a cheaper fix than a new well when there is water below it.

**Do not read a falling level into one reading.** The state reports compare different wells, so a 90-ft median in 2026 does not mean levels rose, and a 120-ft median in 2023 does not mean they fell. If yours is lower than your neighbor’s, compare the pump setting, the depth and the town before worrying. When a pump goes in, a good tech measures the level first, and the same goes for [replacing a pump](https://waterwelldrillingweatherford.com/services/well-pump-replacement/) or [deepening a well](https://waterwelldrillingweatherford.com/services/well-deepening/).

## How was this guide researched?

The figures come from our analysis of the Texas Water Development Board’s Submitted Drillers Reports, extract dated September 25, 2026. We counted Parker County reports of new wells for domestic use with a drilling end date of January 1, 2021 or later (4,746 wells), then kept those that list a static level above the total depth (1,905). Towns are the mailing city on each report.

Static level is what the driller recorded when the well was finished, not a later measurement, and drillers enter it by hand. We did not edit entries. Other sources are Oregon State University’s well water page, the Upper Trinity district’s 2023 plan and one forum thread, which we could only read through a search excerpt. A search for a published Parker County static-level table found none, and a TWDB monitoring-well record we found did not name its aquifer, so we did not use it. We will refresh the numbers when the next extract is available. To check a driller before you hire one, use our [guide to well driller licenses](https://waterwelldrillingweatherford.com/learn/check-well-driller-license-texas/), and if it is time to decide between a repair and a new pump, see [repair or replace a well pump](https://waterwelldrillingweatherford.com/learn/repair-or-replace-well-pump/). For a measured answer on your own well, call a well tech at the number below.

## Frequently asked questions

**What is a normal static water level for a well in Parker County?**

The median is 110 ft below ground, and the middle half of new household wells run from 75 to 180 ft, based on 1,905 Texas Water Development Board driller reports since 2021. Town matters most: the median is 80 ft near Poolville and 180 ft near Aledo, so compare your well with your own area.

**What is the difference between static and pumping water level?**

The static level is where water stands when the pump has been off and the well has rested. The pumping level is lower, because the pump draws the water down while it runs. Oregon State University advises using the static level, not a pumping or recovering one, to judge whether a well is going dry.

**How do I find the static water level of my well?**

Look at the State of Texas Well Report your driller filed, which may list it, or measure it. Oregon State University calls an electric depth gauge the easiest and most common method. Let the well rest several hours first. In Parker County, only 40% of recent new-well reports include a static level.

**How far below the static level should a well pump be set?**

There is no single rule. In Parker County, the median pump sits 100 ft below the static level, and the middle half run 80–130 ft, from 1,729 driller reports. A pump maker told one forum poster his pump should sit no more than 40–50 ft below static, so check your pump's own limit.

**Does a lower static water level mean my well is going dry?**

Not by itself. Different wells vary by town, and 21.8% of new Parker County wells report water 200 ft down or deeper at completion. What matters is the water above the pump while it runs. Oregon State suggests 4–6 readings a year for at least 5 years to see a real trend.

Sources

1. [Texas Water Development Board, Submitted Drillers Reports (extract dated September 25, 2026; our analysis of Parker County new domestic wells, 2021 to 2026)](https://www.twdb.texas.gov/groundwater/data/drillersdb.asp)
2. [Oregon State University Well Water Program, Measuring Well Water Level (page shows copyright 2026)](https://wellwater.oregonstate.edu/well-water/limited-water/measuring-well-water-level)
3. [Upper Trinity Groundwater Conservation District, Groundwater Management Plan (adopted February 16, 2023), on the district's documents page](https://uppertrinitygcd.com/forms-documents/)
4. [Solar-Electric.com forum, thread "pump distance below static water level" (thread date not seen; details taken from a search-result excerpt because the page returned HTTP 403)](https://forum.solar-electric.com/discussion/comment/422699)

## More from the news desk

- Explainer **[2 Wire vs 3 Wire Well Pump: Differences, Cost and Which to Choose](https://waterwelldrillingweatherford.com/news/2-wire-vs-3-wire-well-pump/).**
- Explainer **[Well Maintenance Cost: What a Year of Upkeep Runs in 2026](https://waterwelldrillingweatherford.com/news/well-maintenance-cost/).**
- Explainer **[Well Pump Short Cycling: Why It Happens and How to Stop It](https://waterwelldrillingweatherford.com/news/well-pump-short-cycling/).**

## Ask about your well

Faster by phone, any hour: [(817) 382-3840](tel:+18173823840)
