Skip to content

24/7 live answer

(817) 382-3840
Water Well Drilling Weatherford · TX

Cost Guide

How Much Does Well Pump Replacement Cost in Parker County?

2026 prices for replacing a submersible well pump, based on the pump settings common in Parker County.

Written by , 24-year water well drillerUpdated

Replacing a submersible well pump in Parker County typically costs $1,800 to $4,500 in 2026, including the pump, motor, wire, fittings and labor. Depth drives the price: pumps set around 200 ft, the median near Weatherford, land at the low end, while 280–310 ft settings around Aledo and Granbury cost more.

Water Well Drilling Weatherford prices pump jobs across Parker County every week, and well pump replacement cost comes down to three things: how deep the pump sits, what comes out of the hole with it, and what the new pump needs to push. National averages miss the first one, because Parker County pumps sit deeper than the national typical. If you are wondering whether a pump is due at all, see how long a well pump lasts. If you are weighing a cheaper jet pump, our submersible vs jet pump comparison shows why Parker County depths rule most jets out.

Price by pump setting

Pump settingTypical 2026 replacement costWhere you’ll see it
Around 180–200 ft$1,800–$3,000Peaster, Poolville, Brock, Azle, Weatherford
Around 280 ft$2,200–$4,500Aledo and east Parker County
Around 310 ft$2,500–$5,000Granbury and Hood County
400 ft and deeper$4,000–$6,000+Deep Twin Mountains wells

Settings come from Texas Water Development Board driller reports for new household wells since 2021: medians of about 200 ft near Weatherford, 180 ft around Peaster, Poolville and Brock, 280 ft around Aledo and 310 ft around Granbury. Cost ranges follow HomeGuide’s 2026 depth data (about $1,800–$3,000 at 200 ft and $4,000–$6,000 at 400 ft).

DrillerDB’s 2026 guide gives a simple depth rule: each additional 100 vertical feet adds roughly $500 to $1,000. By that rule, the roughly 110 ft between a Weatherford setting (200 ft) and a Granbury setting (310 ft) adds about $550–$1,100, which matches the gap between the first and third rows above. That arithmetic is ours, from DrillerDB’s figure.

What’s on a typical invoice?

DrillerDB breaks a submersible replacement into these 2026 line items. Its pipe and wire figures are for a 300-ft example, close to Aledo and Granbury pump settings.

Line item2026 range (DrillerDB)
Pump unit$300–$1,500
Labor and extraction$250–$1,500
Drop pipe ($1–$3 per ft, 300-ft example)$300–$900
Submersible wire ($1.50–$2.50 per ft)$150–$750
Check valve and torque arrestor$50–$200
Pitless adapter$100–$300
Permits and inspections$25–$500

DrillerDB also lists labor at $45–$150 an hour plus a $100–$150 callout, and $300–$700 for a hoist rig on deep wells. Pipe and wire together can add $450–$1,650 at 300 ft, which is why two quotes for “a new pump” can be $1,500 apart. Ask each contractor to price the same line items.

What’s in the price

  • Pump and motor, sized by flow (gallons per minute) and total lift.
  • Wire and splice. Longer runs need heavier wire, and the splice should be sealed with a heat-shrink kit.
  • Fittings: torque arrestor, check valves, pitless adapter seal.
  • Labor to pull and set. Deeper sets take longer and may need a pump hoist.
  • Disinfection of the well after it’s opened.

What adds to the bill

  • New drop pipe. Often worth it if the old pipe is corroded or the threads are worn.
  • A control box or switch. Three-wire pumps need a matching control box, and an old pressure switch is cheap to replace while everything is apart.
  • A bigger tank. If the old tank was undersized, the new pump will short-cycle unless the tank is fixed too. Pressure tank replacement typically runs $800–$1,800 installed.
  • A constant-pressure drive, which adds cost up front for steadier pressure.
  • After-hours work. DrillerDB puts emergency or after-hours labor at a 25% to 50% markup.
  • A pump sized for the wrong flow. A pump that outruns a low-yield well can pull the water level down to the intake. Our guide to what a good GPM for a well is covers household flow targets.

What people report paying

Owners online report quotes like $3,700 to replace a pump at 175 ft, $3,800 at 300 ft, and around $6,000 for a 5-horsepower, 230-volt deep-well pump. Setting a pump at 500 ft or more can reach five figures. Those numbers fit the table above. The spread usually comes from pipe, wire and motor size, not from the pump itself.

Does homeowners insurance cover a new well pump?

Usually only when the damage is sudden. DrillerDB’s 2026 guide says standard HO-3 policies cover named perils such as lightning, fire, vandalism or a falling tree, and deny claims for age, wear, corrosion, sediment, or a pump that failed because the well ran dry. An equipment-breakdown rider or home-warranty add-on can cover mechanical failure, typically up to a set limit.

If a storm took the pump out, keep the old pump and the tech’s written finding; see lightning damage to a well pump for what to document. DrillerDB also notes that manufacturer warranties usually cover only the hardware, so the owner still pays the $500–$1,000 labor to pull and reset the pump.

Before you pay for a replacement

Make sure the pump is actually the problem. Pressure switches, control-box capacitors and wiring faults cost $150–$600 to fix and can look exactly like a dead pump. A good service call tests those from the surface first. Line-item prices for those fixes are in our well pump repair cost guide. See repair or replace a well pump and our well pump replacement service.

Bottom line

Budget $1,800–$3,000 for a typical 200-ft pump set near Weatherford and $2,500–$4,500 for deeper Aledo and Hood County settings. Get the price in writing before the pump is pulled, and make sure the quote says whether pipe and wire are being replaced.

Questions about your own well? Call (817) 382-3840. A person answers 24/7.

Sources

  1. HomeGuide, well pump cost by depth (2026)
  2. Angi, well pump replacement cost (2026)
  3. DrillerDB, well pump replacement cost: depth rule, invoice line items, insurance (2026)
  4. Texas Water Development Board, Submitted Drillers Reports (pump settings)

Planning a well or facing a repair? Call a well tech now.

Open 24 hours, 7 days a week. Serving Weatherford & Parker County.

Quick answers

What's the national average cost to replace a well pump?

Angi's 2026 data puts the national average at about $1,897, and DrillerDB reports a typical range of $1,500–$2,827. Parker County's deeper settings push many jobs above those averages.

Does replacing the pump include new pipe and wire?

Not always. A quote that reuses drop pipe and wire is cheaper, but worn pipe or a nicked wire can cause the next failure. Ask for the price with and without new pipe and wire, and for the old parts to be inspected when they come out.

Is a constant-pressure pump worth the extra cost?

It gives steadier pressure and allows a smaller tank, but it adds cost and electronics that can be damaged by lightning. For a household with irrigation or a large house, it's often worth it. For a simple system, a correctly sized standard pump and tank is reliable and cheaper.

More well pump replacement guides

Well Pump Replacement service

Ask about your property

Share the address area and what you're planning. We'll call back with the nearby well depths and a price range.

Faster by phone, any hour: (817) 382-3840

We use your details only to call you back about this request. See our privacy notice.

(817) 382-3840 No water? A person answers 24/7