Most repairs that don't require pulling the pump, such as a pressure switch, control box, capacitor or wiring fault, run $150 to $600 including the call. If the motor or pump end has failed, a submersible replacement at typical Parker County depths runs $1,800 to $4,500. You get the price in writing before any work starts.
24/7 · Weatherford & Parker County
Well Pump Repair for Weatherford Homes & Acreage
No water, pressure that won't build, or a pump that never shuts off. We find the fault with meters at the wellhead, give you a written price, and fix what is actually broken, day or night.
(817) 382-3840 · Open 24 hours, 7 days a week
Call if you see
- No water and the pressure gauge reads zero
- Pump runs but pressure never reaches cut-off
- Breaker trips when the pump starts
- Pump clicks on and off every few seconds
- Spitting faucets, air or sand in the water
- Water returns after resting, then fades again
Last updated
Water Well Drilling Weatherford handles well pump repair for homes, barns and ranches across Weatherford and Parker County, and the first job on every call is finding out what actually failed. A house with no water is not always a dead pump. Often the fault is above ground: a pressure switch with burned contacts, a capacitor that has failed in the control box, a tripped breaker, or a waterlogged tank that has been making the pump start dozens of times an hour. HomeGuide’s 2026 cost data puts electrical faults alone at about 30% of well pump service calls.
What we do on the first visit
We start at the pressure tank and work down the well. The switch, tank pre-charge, supply voltage and running amps are checked first, then the pump wire and motor get an insulation reading from the surface. Together those tests tell us whether the problem is in the house, in the control or in the well. If the pump has to come out, you see the replacement price in writing before we set up to pull it.
The failures behind most no-water calls
Pressure switch
The switch at the tank turns the pump on and off. Its contacts pit and burn with every start, and its small sensing tube clogs with sediment and iron. A failing switch leaves the pump off when the gauge drops, or on when it should stop. It is the cheapest fix on a well and one of the most common.
Control box and capacitor
Three-wire submersible pumps have a control box on the wall with a start capacitor and relay. When the capacitor fails the motor hums, draws high amps and trips the breaker. Summer heat in an unshaded well house and lightning surges during North Texas storm season are the usual culprits.
Wiring and splices
The wire runs 200 ft or more down a typical Parker County well. A splice that wasn’t sealed properly, or insulation rubbed through against the casing, shows up as a low insulation reading. It can be repaired, but it means pulling the pump.
The pump itself
Submersible pumps generally last 8 to 15 years. Sand from Paluxy and Twin Mountains wells wears the impellers, and short cycling overheats the motor. A motor that reads open or grounded, or a pump end that turns but can’t lift water to the surface, means well pump replacement.
When the water level is the problem
Texas Water Development Board driller reports show the median new well near Weatherford finished with water standing about 110 ft down, but around Aledo it is closer to 176 ft, and in dry summers the level drops further while the pump runs. If the level falls to the intake, the pump draws air, loses prime and overheats. We measure the static level when the symptoms point that way. Sometimes the right fix is setting the pump lower, sometimes a smaller pump or a pump protector, and sometimes a conversation about whether the well is going dry.
Paying for the repair
Homeowners policies often cover a pump killed by a lightning strike or power surge but not one that simply wore out. Home warranties frequently cap or exclude well equipment. We write down what failed and why, so you have what your insurer or warranty company needs to process the claim.
Typical cost
$150–$600 for most switch, control and wiring repairs
If the pump itself has failed, replacement at the 180–310 ft settings common in Parker County typically runs $1,800–$4,500.
What's included on every well pump repair call
- Supply voltage and running amps checked at the pressure switch and control box
- Pressure switch contacts, cut-in and cut-out settings and sensing port inspected
- Pressure tank pre-charge measured and reset to 2 psi below cut-in
- Capacitor and relay tested in the control box on three-wire pumps
- Insulation (megohm) reading on the pump wire and motor from the surface
- Check valves and pitless adapter checked for leak-back
- Static water level measured when a dry-running pump is suspected
- Written findings, with repair and replacement prices side by side
Related resources for well pump repair
Well Pump Repair: three ways it gets done
| Item | Do it yourself | Cheapest bid | Done to standard |
|---|---|---|---|
| Finding the fault | Swap parts until it works | Pulls the pump first and replaces it | Surface tests of voltage, amps, switch, tank and wire insulation before anything comes out |
| Pressure switch | Contacts filed and reused | Replaced, setting left at factory | Replaced when pitted, set to the tank pre-charge, sensing port cleared |
| Short cycling | Ignored | Switch replaced, tank left waterlogged | Tank pre-charge and size checked so the pump runs at least a minute per start |
| Dry-running pump | Reset and hope | Bigger pump installed | Water level measured; pump set, sized or protected against running dry |
| Afterwards | Water back on | Water back on | Full cycles tested, well chlorinated if opened, findings written down |
How well pump repair works, start to finish
-
Call and triage
Tell us what the gauge reads, whether the breaker tripped and when the water stopped. We will tell you what is safe to try before we arrive.
-
Surface tests first
Voltage, amp draw, switch, tank and wire insulation are tested from the surface. Most faults show up here without pulling the pump.
-
Written options
You get the cause, the fix and the price in writing. If the pump has to come out, you see the replacement price before we pull it.
-
Repair, test, disinfect
After the repair we run full pressure cycles, check flow at a hose bib and chlorinate the well if the cap came off.
On the job
Need well pump repair in Weatherford or Parker County?
A person answers 24/7 and prices the job before work starts.
Well Pump Repair questions
How much does well pump repair cost in Weatherford?
How do I know if it's the pump or the pressure switch?
Look at the gauge and listen at the tank. If the gauge is below the cut-in pressure (usually 30 or 40 psi) and the switch contacts are open, the switch or its sensing port is the likely fault. If the contacts are closed, power is reaching the pump and the gauge still won't rise, the problem is down the well: the pump, the drop pipe or the water level.
Can a plumber fix a well pump in Texas?
A plumber can repair house plumbing and often the pressure tank. Installing, pulling or repairing the pump in the well for pay requires a pump installer license from the Texas Department of Licensing and Regulation under Occupations Code chapter 1902. Ask for the license number and check it on TDLR's public search.
Why does my pump run but no water comes out?
The usual causes are a split or unthreaded drop pipe, a worn pump end, a stuck check valve, or a water level that has fallen to the pump intake. A pump that keeps running without delivering water can overheat and fail, so turn it off at the breaker until it has been checked. Our no-water guide covers what to look at first.
Do you answer after hours and on weekends?
Yes. The phone is answered 24 hours a day, 7 days a week. After-hours work is priced before we roll, and if the fix can safely wait until morning we will tell you so.
Sources
Related well services
-
Well Pump Replacement
Submersible pumps sized to your well's depth, water level and household demand, set on new drop pipe and wire when the old run is worn.
-
Well Pressure Tank Replacement
Waterlogged tanks, short-cycling pumps and pressure that surges and drops. We size the tank to the pump so the motor stops wearing itself out.
-
Water Well Service & Repair
Flow tests, well caps, wiring, casing and chlorination for existing wells, plus one number to call when anything on the system acts up.
Request well pump repair
Tell us what the well is doing and where it is. Not urgent? We'll call back first thing.
Faster by phone, any hour: (817) 382-3840