Skip to content

24/7 live answer

(817) 382-3840
Water Well Drilling Weatherford · TX

Cost Guide

How Much Does Pressure Tank Replacement Cost?

2026 prices to replace a well pressure tank, and why sizing it to the pump matters more than the tank's price.

Written by , 24-year water well drillerUpdated

Replacing a well pressure tank typically costs $800 to $1,800 installed in 2026, including the tank, tank tee, gauge, a new pressure switch and labor. HomeGuide puts the average at $800–$1,500. Larger tanks, crowded well houses and added components push the price higher, up to about $3,500 for big or difficult installs.

Water Well Drilling Weatherford replaces pressure tanks across Parker County, and pressure tank replacement cost is one of the easiest numbers to pin down in well work. It’s also one of the most important jobs to get right, because the tank decides how hard the pump works.

What the price covers

ItemTypical 2026 cost
Bladder or diaphragm tank (20–80+ gallons)$200–$1,500
Tank tee, gauge, drain, relief valvePriced with the job
Pressure switch (replaced while the system is apart)$150–$300 installed
Labor: drain, swap, set pre-charge, test cyclesIncluded in most quotes
Typical installed total$800–$1,800

HomeGuide’s 2026 average for a replacement is $800–$1,500, with a range up to about $3,500 for large or hard-to-reach installs. Angi’s lower average, $300–$700, mostly reflects smaller tanks with little extra work.

Size is set by the pump

Franklin Electric’s submersible motor manual says to run a motor at least one minute per start so the heat from starting can dissipate, and to keep the starts per day as low as practical. A tank only gives up part of its nominal volume between pump cycles, called drawdown. So the test is simple: the tank’s drawdown in gallons should be at least your pump’s gpm. A 10-gpm pump needs about 10 gallons of drawdown to run one minute.

Pentair’s Sta-Rite ProSource Plus manual publishes drawdown per cycle by switch setting:

Tank model (nominal)20/40 psi30/50 psi40/60 psi
PSP19 (about 19 gal)6.9 gal5.8 gal5.0 gal
PSP35 (about 35 gal)12.7 gal10.7 gal9.3 gal
PSP50 (about 50 gal)18.3 gal15.5 gal13.4 gal
PSP85 (about 85 gal)30.0 gal26.0 gal22.0 gal

Read it against your pump. A 10-gpm pump on a 30/50 switch is fine with the 35-gallon tank (10.7 gal, about 64 seconds per run) but short on the same tank at 40/60 (9.3 gal, about 56 seconds). A 15-gpm pump wants the 50-gallon class at 30/50. These numbers are one manufacturer’s steel tanks; other brands differ by a gallon or two, so check the data sheet for the tank you buy. Raising the switch pressure shrinks drawdown, which is why moving from 30/50 to 40/60 can bring short-cycling back. See 30/50 vs 40/60 pressure switch and what size pressure tank do I need.

Set the pre-charge before you fill it

Pentair’s manual sets the tank’s air pre-charge 2 psi below the pump cut-in: 18 psi for a 20/40 switch, 28 psi for 30/50 and 38 psi for 40/60, measured with no water in the tank. A new tank shipped at 38 psi and wired to a 30/50 switch loses drawdown from day one. It is the one setting most replacement jobs get wrong, and it takes a tire gauge to check.

Cross-check: one retailer’s price list

Prices vary by who sells the tank. Mid Atlantic Water, a well-water supplier, listed in October 2026 an installed replacement by a plumber at $800 to $1,800, labor for a straightforward swap at $200 to $500, and a tank and pump replaced together at $2,500 to $5,000 or more. Its bare Well-X-Trol tanks ran about $340–$370 for a 20-gallon and $700–$1,150 for a 44-gallon. This is a seller’s page, not an independent survey, but its installed range matches HomeGuide’s. For the pump-side numbers, see well pump repair cost.

Why a cheap tank job can be expensive

A waterlogged tank makes the pump start every few seconds. Each start heats the motor windings and wears the switch contacts. The tank costs a few hundred dollars; a submersible pump at Parker County depths typically costs $1,800–$4,500 to replace. If your pump clicks on and off during a shower, the tank is the cheapest thing you’ll fix this year. See signs of a bad pressure tank.

When to replace instead of recharge

An old galvanized tank without a bladder can be recharged with air, but it will keep losing its charge. A bladder tank that spits water at the air valve has a torn bladder and can’t be fixed. Replace it. A bladder tank that has simply lost some air can be recharged, but if it keeps losing air, the valve or bladder is failing.

What drives the price up

Big tanks for irrigation or constant-pressure systems, two-tank setups, tight or unvented well houses, corroded fittings that snap during removal, and after-hours calls. We quote the whole job in writing before draining the system. See well pressure tank replacement.

Bottom line

Expect $800–$1,800 for a typical household tank replacement. The bigger saving is what a correctly sized tank prevents: a pump that short-cycles to death, which costs $1,800–$4,500 to replace at Parker County depths.

Questions about your own well? Call (817) 382-3840. A person answers 24/7.

Sources

  1. HomeGuide, cost to replace a well pressure tank (2026)
  2. Angi, well tank replacement cost (2026)
  3. Pentair Sta-Rite, ProSource Plus steel pressure tanks manual (pre-charge chart, Chart II drawdown)
  4. Mid Atlantic Water, well water pressure tank cost (updated October 14, 2026)
  5. Franklin Electric, Submersible Motors AIM manual (minimum run time, starts per day)

Planning a well or facing a repair? Call a well tech now.

Open 24 hours, 7 days a week. Serving Weatherford & Parker County.

Quick answers

How much does the tank itself cost?

HomeGuide puts the tank alone at about $200–$1,500, depending on capacity and brand. The rest of the cost is fittings, a switch and gauge, and labor to drain the system, swap the tank and set the pre-charge.

Can I replace a pressure tank myself?

Homeowners do, but the details matter: kill the power, drain the system, set the pre-charge 2 psi below the cut-in pressure before filling, and size the tank to the pump. A tank installed with the wrong pre-charge or size can still short-cycle the pump.

How long does a new tank last?

A quality bladder tank typically lasts 10–15 years. Cheaper tanks can fail in about five. Correct pre-charge and sizing are the biggest factors in how long it lasts.

More well pressure tank replacement guides

Well Pressure Tank Replacement service

Ask about your property

Share the address area and what you're planning. We'll call back with the nearby well depths and a price range.

Faster by phone, any hour: (817) 382-3840

We use your details only to call you back about this request. See our privacy notice.

(817) 382-3840 No water? A person answers 24/7