Skip to content

24/7 live answer

(817) 382-3840
Water Well Drilling Weatherford · TX

Urgent Help

Why Is the Water Pressure Low on My Well?

Low pressure on a private well has a short list of causes. The pressure gauge and a few minutes of observation usually tell them apart.

Written by , 24-year water well drillerUpdated

Low water pressure on a well usually comes from one of five things: a clogged sediment filter, a pressure switch set too low, a waterlogged pressure tank, a leak between the well and the house, or a worn pump or falling water level. Watch the pressure gauge while water runs. How it behaves points to the cause.

Water Well Drilling Weatherford diagnoses low water pressure on well systems across Parker County. The pressure gauge next to your tank is the best diagnostic tool you own. Open a tap in the house, then watch the gauge and listen to the pump for a couple of minutes.

What the gauge tells you

What you seeMost likely cause
Gauge reads normal (e.g., 40–60 psi) but one fixture is weakA clogged aerator, showerhead or fixture valve
Gauge normal, whole house weakA clogged sediment or whole-house filter, or a partly closed valve
Pressure drops fast and the pump starts every few secondsA waterlogged pressure tank (lost air charge or failed bladder)
Pump runs a long time and barely reaches cut-outA worn pump, a leak in the drop pipe, or a falling water level
Pump runs constantly, yard wet between well and houseA broken line (more causes: well pump running constantly)
Pressure fine, then fades during long showers or irrigationThe well or pump can’t keep up with demand

The cheap fixes first

  • Sediment filter. Parker County water carries iron and grit, and cartridge filters clog. If the pressure after the filter is lower than before it, change the cartridge.
  • Switch setting. A 30/50 switch gives lower pressure than 40/60 (see our 30/50 vs 40/60 pressure switch comparison). The setting can be raised if the pump has the capacity, but the tank’s pre-charge must be reset to 2 psi below the new cut-in. Our step-by-step on how to adjust a well pressure switch covers the order of the steps, and our guide on how to increase well water pressure ranks every fix from cheapest to costliest.
  • Prime. An above-ground jet pump that has lost its prime delivers little or no water. Our guide on how to prime a well pump shows the steps and when a repeat means a leak.
  • Sensing port. The small tube under the pressure switch clogs with sediment, making the switch act erratically. Cleaning it or replacing the switch is a $150–$300 job.

Why won’t my pump reach 40 psi?

A pump that runs but stalls short of the cut-off pressure has run out of one of three things. The checks below take about ten minutes and cost nothing.

  1. Read the gauge at rest. With no water running, the gauge should sit at the cut-off pressure (50 on a 30/50 switch, 60 on a 40/60). If it rests lower and the pump is off, the switch is stopping the pump early or the gauge is failing.
  2. Watch the climb. Open a tap and close it. Time how long the needle takes to climb and note where it stops. If it crawls and stalls below cut-off, the pump is not building the pressure.
  3. Check the tank charge. With the breaker off and the tank drained, the air valve should read 2 psi below cut-in, which Pentair’s tank manual charts as 28 psi for a 30/50 switch and 38 psi for a 40/60. Too little air makes the pump cycle, but it does not stop it reaching cut-off.
  4. Compare the setting with the pump. Pentair’s switch instructions cap cut-off at 60 psi and call for at least 5 psi of margin under the pump’s maximum pressure. A shallow-well jet pump or an older submersible may not have 60 psi in it, and no switch change fixes that.

If the pump runs, the tank charge is right and the gauge still stalls below cut-off, the cause is in the pump, the drop pipe or the water level. Switch the breaker off and call. For the reverse problem, wanting more pressure from a healthy system, see how to increase well water pressure.

What to tell the tech

Calls go faster when you can say: where the gauge rests, where the pump starts and stops, how long the climb to cut-off takes, whether the filter was changed recently, and whether the weakness shows up at night or after heavy use. That separates a tank or switch visit from a pump and water-level visit, and it tells us what to bring.

When it’s the tank

If pressure falls quickly and the pump starts every few seconds, the tank has lost its air cushion. That’s more than a comfort problem. Submersible motors need at least a minute of run time per start. See signs of a bad pressure tank and pressure tank replacement cost.

When it’s the pump or the well

A pump that runs long and struggles to reach cut-out pressure is either worn, losing water through a split drop pipe, or pulling from a water level that has dropped toward the intake. Near Weatherford, new wells finish with water about 110 ft down. Around Aledo it’s closer to 176 ft, and in dry summers the level falls while the pump runs (see the static water level numbers by town). We check amp draw and measure the water level before recommending a new pump. Sometimes lowering the existing pump or adding a storage tank is the real fix.

When to stop and call

If the pump runs continuously without reaching cut-out, turn the breaker off and call. That’s how pumps overheat. For the rest, a daytime service call is fine. See well pump repair.

Bottom line

Check the filter and the gauge first. They explain most low-pressure complaints and cost little to fix. If the gauge won't reach the cut-out pressure, or the pump runs constantly, have the pump and water level checked before the motor pays the price.

Questions about your own well? Call (817) 382-3840. A person answers 24/7.

Sources

  1. Pentair, Adjusting Well Pump Pressure Switches (U80-129): 2½ psi per turn, 20 psi minimum cut-in, 60 psi maximum cut-off
  2. Pentair Sta-Rite ProSource Plus steel pressure tanks manual (pre-charge 2 psi below cut-in)
  3. Franklin Electric, Submersible Motors AIM manual (tank sizing, run time)
  4. HomeGuide, well pump repair cost (2026)
  5. HomeGuide, cost to replace a well pressure tank (2026)

Planning a well or facing a repair? Call a well tech now.

Open 24 hours, 7 days a week. Serving Weatherford & Parker County.

Quick answers

What should my well pressure be?

Most household systems run on a 30/50 or 40/60 psi switch. The pump turns on at the lower number and off at the higher one. Pressure swinging between those two is normal.

Can I just turn up the pressure switch?

A small adjustment is possible, but only if the pump can reach the new cut-out pressure and the tank pre-charge is reset to match (2 psi below cut-in). Turning it up on a weak pump can leave the pump running nonstop.

Why is pressure fine in the morning and weak at night?

Often the well can't keep up with evening demand. The water level falls while the pump runs, and pressure sags. A storage tank with a booster pump, or a lower pump setting, usually fixes it.

More well pressure tank replacement guides

Well Pressure Tank Replacement service

Ask about your property

Share the address area and what you're planning. We'll call back with the nearby well depths and a price range.

Faster by phone, any hour: (817) 382-3840

We use your details only to call you back about this request. See our privacy notice.

(817) 382-3840 No water? A person answers 24/7